Viper Automobile Alarm 160XVL User Manual

Model 160XVL

Owner's Guide

HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING

WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS

WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REIN-

STALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE

EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS OR ITS SUB-

SIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF

CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL

APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM

AGAINST DIRECTED ELECTRONICS SHALL BE STRICTLY LIMITED TO THE AUTHORIZED

DIRECTED ELECTRONICS DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED ELEC-

TRONICS SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER,

INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL

DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL

LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE

ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR

REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow lim-

itations on how long an implied warranty will last or the exclusion or limitation of

incidental or consequential damages. This warranty gives you specific legal rights and

you may also have other rights that vary from State to State.

This product may be covered by a Guaranteed Protection Plan ("GPP"). See your

authorized Directed Electronics dealer for details of the plan or call Directed

Electronics Customer Service at 1-800-876-0800. Directed Electronics security systems,

including this unit, are deterrents against possible theft. Directed Electronics is not

offering a guarantee or insurance against vandalism, damage or theft of the automo-

bile, its parts or contents; and hereby expressly disclaims any liability whatsoever,

including without limitation, liability for theft, damage and/or vandalism. Directed

Electronics does not and has not authorized any person or entity to create for it any

other obligation, promise, duty or obligation in connection with this security system.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

■ Date of purchase

■ Your full name and address

■ Authorized dealer's company name and address

■ Type of alarm installed

■ Year, make, model and color of the automobile

■ Automobile license number

■ Vehicle identification number

■ All security options installed on automobile

■ Installation receipts

Table of Contents

Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . i

Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

What is Included

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Your Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FCC/ID Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Transmitter Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Warning! Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Disabling the Starter Kill Without a Transmitter. . . . . . . . . . . . . . . . . . . . . . . 11

Valet Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Rear Defogger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Valet Take-Over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Short-Run/Turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Timer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Starter Anti-Grind Circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Disabling the Remote Start System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Rapid Resume Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

nComfort closure is a programming option which closes the vehicle’s windows

after remote locking.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Convenience Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Quick Reference Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Standard Configuration

controls the Arm/Panic ON/Panic OFF function.

controls the Disarm function.

controls Silent Mode™and an Auxiliary Output.

controls Remote Start.

controls Timer mode.

controls Turbo/Short Run.

controls Channel 4 output.

+ +

controls Rear Defroster.

What is Included

■ The control module

■ A Venom SST receiver/antenna

■ Two four-button transmitters

■ The blue status LED indicator light

■ A push-button Valet button

■ Your warranty registration

■ A shut-down toggle switch

Important Information

Congratulations on the purchase of your remote start keyless entry

system. Due to the complexity of this system, it must be installed

by an authorized dealer only. Installation of this product by any-

one other than an authorized dealer voids the warranty. All deal-

ers are provided with a preprinted dealer certificate to verify that

they are authorized.

By carefully reading this Owner's Guide prior to using your system,

you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by

accessing the Directed Electronics internet website at

www.directed.com.

System Maintenance

The system requires no specific maintenance. Your remote is powered

by two small, lightweight 3-volt lithium batteries that will last

approximately one year under normal use. When the battery begins to

weaken, operating range will be reduced and the LED on the remote

will dim.

Your Warranty

Your warranty registration must be completely filled out and

returned within 10 days of purchase. Your product warranty

will not be validated if your warranty registration is not returned.

Make sure you receive the warranty registration from your dealer.

It is also necessary to keep your proof of purchase, which reflects

that the product was installed by an authorized dealer.

FCC/ID Notice

This device complies with Part 15 of FCC rules. Operation is subject

to the following conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference re-

ceived, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this device.

HHU, hand held unit

To satisfy FCC RF exposure compliance requirements, this device should

be used in hand-held, hand operated configurations only. The device

and its antenna must maintain a separation distance of 20 cm or more

from the person’s body, except for the hand and wrists, to satisfy RF

exposure compliance. This device is designed to be used in a person’s

hands and its operating configurations do not support normal trans-

missions while it is carried in pockets or holsters next to a persons’

body.

Caution

This product is designed for fuel injected, automatic transmission

vehicles only. Use of this product in a standard transmission vehi-

cle is dangerous and contrary to the product's intended use.

Transmitter Functions

The receiver uses a computer-based learn routine to learn the

transmitter buttons. This makes it possible to assign any specific

transmitter button, or combination of buttons, to any receiver

function. The transmitter initially comes programmed with the

Standard Configuration, but may also be customized by an autho-

rized dealer. The transmitter buttons indicated in all of the instruc-

tions in this manual correspond to a Standard Configuration trans-

mitter.

Standard Configuration

Button

The arming and panic functions are controlled by pressing

the transmitter for one second.

Button

The disarm function is controlled by pressing

ter for one second.

on the transmit-

Button

Silent Mode^™and an optional auxiliary function are controlled

by pressing . Silent Mode works by pressing for less than

one second. An optional auxiliary function, such as

trunk release, is controlled by pressing and holding

1.5 seconds.

for

Button

The remote start function of your system is controlled by pressing

this button twice within 3 seconds.

and

Buttons

An optional auxiliary convenience or expansion function that you

have added to your system can be activated by pressing these but-

tons simultaneously.

The auxiliary output controls __________________________.

Buttons

When simultaneously pressed these buttons control the rear win-

dow defogger during remote starting.

Using Your System

Warning! Safety First

The following safety warnings must be observed at all times:

■ Due to the complexity of this system, installation of this

product must only be performed by an authorized Directed

Electronics dealer.

■ When properly installed, this system can start the vehicle via

a command signal from the remote control transmitter.

Therefore, never operate the system in an enclosed area or

partially enclosed area without ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or

when having the vehicle serviced, the remote start system

must be disabled using the installed toggle switch. It is the

user's sole responsibility to properly handle and keep out of

reach from children all remote control transmitters to assure that

the system does not unintentionally remote start the vehicle.

THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR

IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE

ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE

AREA MUST AT ALL TIMES REMAIN CLOSED. These precau-

tions are the sole responsibility of the user.

■ Use of this product in a manner contrary to its intended mode

of operation may result in property damage, personal injury,

or death. (1) Never remotely start the vehicle with the vehi-

cle in gear, and (2) Never remotely start the vehicle with the

keys in the ignition. The user must also have the neutral safe-

ty feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This

testing should be performed by an authorized Directed

Electronics dealer in accordance with the Safety Check out-

lined in the product installation guide. If the vehicle starts in

gear, cease remote start operation immediately and consult

with the authorized Directed Electronics dealer to fix the

problem.

■ After the remote start module has been installed, contact your

authorized dealer to have him or her test the remote start

module by performing the Safety Check outlined in the prod-

uct installation guide. If the vehicle starts when performing

the Neutral Safety Shutdown Circuit test, the remote start unit

has not been properly installed. The remote start module must

be removed or the installer must properly reinstall the remote

start system so that the vehicle does not start in gear. All

installations must be performed by an authorized Directed

Electronics dealer. OPERATION OF THE REMOTE START MOD-

ULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS

INTENDED MODE OF OPERATION. OPERATING THE REMOTE

START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN

PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMME-

DIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSIS-

TANCE OF AN AUTHORIZED DIRECTED ELECTRONICS DEALER

TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START

MODULE. DIRECTED ELECTRONICS WILL NOT BE HELD

RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLA-

TION COSTS.

Arming

Pressing

for one second arms the system by activating the

starter kill and locking the doors (if the door locks are connected).

The horn will honk (if connected) and the parking lights will flash

once to confirm arming of the system. While the system is armed,

the status LED will flash once per second. The Failsafe^®Starter Kill

(if installed) will also prevent the vehicle’s starter from cranking.

The system can also be programmed to arm the optional Failsafe^®

Starter Kill automatically (called Passive Mode). If the system has

been programmed for Passive Mode, the Failsafe^®Starter Kill will

automatically activate 30 seconds after the ignition has been

turned off. After the ignition has been turned off, the status LED

will flash rapidly to indicate that the system is in Passive Mode.

If Passive Mode has been programmed on, then it is also possible

to program the system for Passive Locking. With Passive Locking,

the vehicle doors lock automatically at the same time that the

Failsafe^®Starter Kill is activated. If Passive Locking is programmed

on, care must be taken to prevent the keys from being locked in the

vehicle.

NOTE: For Passive Mode to be effective, the Failsafe^®Starter Kill relay

must be installed.

Disarming

Pressing

for one second disarms the system and unlocks the

doors (if connected). The horn will honk twice (if connected) and

the parking lights will flash twice to confirm disarming of the sys-

tem. The optional Failsafe^®Starter Kill will be deactivated. The sta-

tus LED will turn off, unless the system is programmed for Passive

Mode. In Passive Mode, the status LED will flash rapidly when the

system is disarmed. This indicates that the system will re-engage

the starter kill and re-lock the doors (if Passive Locking has been

programmed) in 30 seconds unless the ignition is turned on.

Disabling the Starter Kill Without a Transmitter

If your remote transmitter is lost or damaged, you can manually

override the starter kill. To do this, you must have the vehicle's

ignition key and know where the Valet button is located. Be sure

to check with the installer for the location of the Valet button.

To override the starter kill, turn

the ignition on and press the

Valet button within 10 seconds.

DRW-35

The status LED will stop flashing

and the vehicle should start. If it does not start,

you may have waited too long; turn the ignition off and repeat the

process.

LOCATION OF VALET BUTTON_____________________________

Valet Mode

You can prevent your system from automatically activating the

Failsafe^®Starter Kill and locking the doors by using Valet Mode.

This is very useful when washing the vehicle or having it serviced.

In Valet Mode, the starter kill cannot be activated, even with the

transmitter, but all convenience functions (door locks, remote

start, etc.) will continue to work normally.

To enter or exit Valet Mode:

1. Turn the ignition on.

2. Turn the ignition off.

3. Press and release the Valet

button within 10 seconds.

DRW-35

The status LED will light steadily if you are entering Valet Mode

and will turn off if you are exiting Valet Mode.

Panic Mode

If you are threatened in or near your vehicle, you can attract

attention by triggering the system with your transmitter. Just

press

for 1.5 seconds to enter Panic Mode. In Panic Mode, the

horn will honk and the parking lights will flash for 30 seconds. To

stop Panic Mode at any time, press

transmitter.

, or

on the

NOTE: In order for Panic Mode to be effective, the vehicle’s horn (or

optional siren) as well as the vehicle's parking lights must be

connected.

Remote Start

This feature allows you to remotely start and run your vehicle for

a programmable period of time. This makes it possible to warm up

the engine, as well as adjust the interior temperature of the vehi-

cle with the climate control system. If interior heating or cooling

is desired, the climate controls must be preset, and the fan blower

must be set to the desired level prior to remote starting the

vehicle.

IMPORTANT! (1) Never remotely start the vehicle with the vehicle

in gear, and (2) Never remotely start the vehicle with the key in the

ignition.

To remote start the vehicle:

1. Press the

mitter.

button twice within 3 seconds on the trans-

2. The parking lights will flash to confirm that the vehicle will

attempt to start.

3. Release the

button as soon as the parking lights flash.

(In gasoline vehicles, the engine will start 4 seconds after

the parking lights flash. In diesel vehicles, the engine will

start when the WAIT-TO-START indicator on the vehicle's dash

goes out or the timer has expired.)

4. Once the vehicle has started, it will run for the pre-program-

med period of time (12, 24, or 60 minutes) or until a shut-

down input is triggered.

When you are ready to drive the vehicle:

1. Insert the ignition key and

turn it to the ON (not the

START) position.

Press the brake pedal.

NOTE: If the brake pedal is pressed before the key is in the ON position,

the engine will shut down.

While the vehicle is running during remote start operation, the

system will monitor the vehicle and will automatically shut down the

engine if the system receives any of the following shut-down inputs:

■ The brake pedal is pressed.

■ The hood is opened.

■ The shutdown toggle switch is put into the OFF position.

■ The pre-programmed run time (12, 24, or 60 minutes) has elapsed.

■ Transmitter button

is pressed twice in 3 seconds to start

the vehicle.

Rear Defogger

To turn the rear defogger output OFF:

1. Simultaneously press & release the

on the remote control.

buttons

2. The lights will flash 2 times.

3. The rear defogger output will no longer activate when the

vehicle is remote started.

NOTE: If the remote start is on the parking lights will turn off then flash

2-times before returning to their normal output and the defogger out-

put, if active, will cease.

To turn the rear defogger output ON:

1. Simultaneously press & release the

on the remote control.

buttons

2. The lights will flash 3 times.

3. The rear defogger output will once again activate when the

vehicle is remote started.

NOTE: If the remote start is on the lights will turn off then flash 3-times

before returning to their normal output and the defogger output will

activate as programmed.

Valet Take-Over

The Valet Take-Over feature allows the vehicle to remain running

after the key has been removed from the ignition. This feature is

useful for occasions when you wish to exit and lock the vehicle for

short periods of time, but would like to leave the motor running

and the climate controls on.

To perform Valet Take-Over:

1. Before turning off the engine, press and release

on the

transmitter twice in 3 seconds (or press and release the

optional momentary switch).

2. Turn the ignition key to the OFF position. (The engine will

stay running.)

3. Once the vehicle has started, it will run for the pre-pro-

grammed period of time (12, 24, or 60 minutes) or until a

shutdown input is triggered.

Short-Run/Turbo

Short-run turbo mode keeps the engine running after arriving at

you destination for a programmable period of 1, 3 ,5 or 10 min-

utes. This allows the system’s timer to conveniently cool down the

turbo after you have left the vehicle.

To activate:

1. Park the vehicle and set parking brake.

2. Remove your foot from the brake pedal and leave the engine

running.

3. Press and release the

and

buttons at the same time.

4. The lights will flash to indicate the remote start has entered

short run turbo mode.

5. Turn off the key, the engine will keep running.

6. Exit and secure the vehicle.

7. The engine will turn off after the programmed run time.

Timer Mode

By pressing the remote

and

buttons the parking

lights will flash 4 times and then start the vehicle and run for the

set duration. The remote start can be shut off by the transmitter

by pressing the remote start button

and remain in timer

mode, but if any other shut down zones or the ignition becomes

active the timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. A 1-second delay will start.

4. The system will start the car and will run for the specified

duration, unless shut down by the remote start button

. If shut down with the remote start button

will remain in timer mode.

the system

5. The system will start every 3 hours until canceled by the

brake, hood, or neutral safety shut-down wires.

important Timer Mode should be used only in

open areas. Never start and run the vehicle in an

enclosed space such as a garage or carport.

To exit timer mode, turn the ignition switch on any time the

engine is running. The parking lights will flash 4 times, indicating

timer mode has been exited.

5. The system will start every 3 hours until canceled by the

brake, hood, or neutral safety shut-down wires.

IMPORTANT! Timer Mode should be used only

in open areas. Never start and run the vehicle

in an enclosed space such as a garage or

carport.

Starter Anti-Grind Circuitry

Whenever the vehicle is remote started, advanced anti-grind cir-

cuitry prevents the starter from engaging, even if the key is turned

to the start position. This prevents damage to the starter motor if

the key is turned to the start position during remote start operation.

NOTE: Anti-grind circuitry only works when the remote start system is

operating the motor and the Failsafe^®Starter Kill relay is installed.

Disabling the Remote Start System

This feature allows your system's remote start unit to be tem-

porarily disabled to prevent the vehicle from being remote started

accidentally. This feature is useful if the vehicle is being serviced

or stored in an enclosed area. To disable the remote start, move

the shutdown toggle switch to the OFF position. The switch can

be installed in a location of your choice. Check with your installer

for recommended locations.

LOCATION OF SHUTDOWN SWITCH_________________________

Rapid Resume Logic

This Directed Electronics system will store its current state to non-

volatile memory. If power is lost and then reconnected the system

will recall the stored state from memory. This means if the unit is

in Valet Mode and the battery is disconnected for any reason, such

as servicing the car, when the battery is reconnected the unit will

still be in Valet Mode. This applies to all states of the system

including arm, disarm, and Valet Mode.

Programming Options

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some may

require additional installation labor. This system's programming

options are listed below, with the factory default settings in bold:

■ 12, 24, or 60 minute run time. your system can be pro-

grammed to allow the vehicle to run for 12, 24, or 60 min-

utes when remote started.

■ 3, 6, 9, or 12 minute timer mode run time. Your system can

be programmed to allow the vehicle to run for 3, 6, 9, or 12

minutes when remote started in timer mode. Can be set up to

16 minutes by your installer.

■ Comfort closure is a programming option which closes the

vehicle’s windows after remote locking.

■ Parking lights flashing or constant. Your system can be pro-

grammed to either flash or to turn on the parking lights con-

stantly during the entire remote start operation.

■ Passive Mode or Active Mode. In Passive Mode the Failsafe^®

Starter Kill will automatically activate 30 seconds after the

ignition has been turned off.

■ Ignition switch-controlled door-locking on or off. With this

feature on, the doors will lock 3 seconds after the ignition

key is turned on, and unlock when the ignition key is turned off.

■ Passive Locking or Active Locking (doors lock only with the

transmitter). With Passive Locking, the vehicle doors lock

automatically 30 seconds after the ignition has been turned

off. Passive Locking can only be selected when the system

has been programmed for Passive Mode.

■ The horn honk confirmations for locking and unlocking can be

programmed on or off. In order for this feature to be pro-

grammed on, the horn must be connected to the system.

Glossary of Terms

Control Unit: The “brain” of your system. Usually hidden under-

neath the dash area of the vehicle. It houses the microprocessor

which monitors your vehicle and controls all system functions.

Failsafe Starter Kill: An automatic switch controlled by your sys-

tem which prevents the vehicle’s starter from cranking whenever

the system is armed. The vehicle is never prevented from cranking

when the system is disarmed, in Valet Mode, or if the starter kill

switch itself fails. Your system has feature-ready circuitry for the

starter kill, however installation may require additional labor.

LED: A blue light mounted at a discretionary location inside the

vehicle. It is used to indicate the status of your system.

Transmitter: A hand-held, remote control which operates the var-

ious functions of your system.

Valet Button: A small push button mounted at a discretionary

location inside the vehicle. It is used to override the Failsafe^®

Starter Kill when a transmitter is lost or damaged, or to enter or

exit Valet Mode.

Convenience Expansions

Listed below are some of the many expansion options available for

use with your system. Some options may require additional parts

and/or labor. Please consult with your dealer for a complete list of

options available for use with this system.

Domelight Supervision: The domelight will illuminate for 30

seconds each time the system is disarmed using the transmitter.

This is useful for seeing inside the vehicle at night prior to

entering it.

Power Door Lock Control: Your system is capable of controlling

many types of power door lock systems; however, some door lock

systems may require extra parts. Consult with your dealer to deter-

mine which type of locks your vehicle uses. If power locks are

connected, the system can be programmed to lock the doors auto-

matically 30 seconds after the ignition has been turned off. The

system can also be programmed to lock the doors when the ignition

is turned on and to unlock them when the ignition is turned off.

Power Trunk Release: The system’s auxiliary output can be pro-

grammed to operate a factory power release for the vehicle's trunk

or hatch. If the factory release is not power-activated, Directed

Electronics 522T trunk-release solenoid can often be added.

Power Window Control: Power window control is provided with

Directed Electronics 529T or 530T systems. The 529T system will

roll up two windows automatically when the system is armed, or

roll two windows down by using the transmitter. The 530T will roll

two windows both up and down. The 530T also provides one touch

switch operation.

Progressive Door Unlocking: For added security, your system can

be configured to unlock the driver’s door only, leaving the pas-

senger doors locked. Pressing the unlock button an additional time

will unlock the passenger doors. This option requires additional

parts and labor.

Auxiliary Outputs Linked to Arm/Disarm/Remote Start: For

added convenience the auxiliary outputs can be used to position

the driver’s seat to a preset position on an Arm, Disarm, or Remote

Start command from the remote.

Notes

Quick Reference Guide

To arm using your remote

■ To arm the system press

for one second. The doors will lock (if con-

nected). The LED will begin to flash. The vehicle’s horn (if connected)

will honk and the parking lights will flash once to confirm arming.

To disarm using your remote

■ To disarm the system press

for one second. The doors will unlock (if

connected). The vehicle’s horn (if connected) will honk twice and the

parking lights will flash twice.

Disabling the Failsafe^®Starter Kill without a transmitter

■ Turn on the ignition. Press and release the Valet button within 10 sec-

onds. The LED will stop flashing and the vehicle should start.

To remote start the vehicle

■ Press

twice within 3 seconds. The parking lights will turn on (if con-

nected) and the vehicle will start and run for the programmed duration.

To enter or exit Valet Mode

■ Turn the ignition to the "ON" position. Turn the ignition back off. Press

and release the Valet button within 10 seconds. The status LED will light

steadily if you have entered Valet Mode. To exit Valet Mode, repeat the

steps above. The LED will turn off when exiting Valet Mode.

To activate Panic Mode

■ Press and hold

for 1.5 seconds.

To activate Timer Mode

■ Press

and

to start the vehicle, and run it for the set duration.

To activate Turbo Mode

■ Park the vehicle and set parking brake. Remove your foot from the brake pedal

and leave the engine running. Press and release the

and

buttons.

To disable the remote start system

■ To disable the remote start, move the shutdown toggle switch to the OFF

position.

Location of Shutdown Switch______________________________

Valet Takeover

■ Press and release

on the transmitter twice in 3 seconds. Turn the

ignition key to the OFF position. Once the vehicle has started, it will run

for the pre-programmed period of time (12, 24, or 60 minutes).

Rear Window Defogger

■ Press the ,

and

buttons simultaneously to turn the defogger

on or off when remote starting. When a remote start is initiated, the

parking lights will flash 2-times if the defogger is set to off, and will

flash 3-times if the defogger is set to on.

The company behind this system is Directed Electronics

Since its inception, Directed Electronics has had one purpose, to provide consumers

with the finest vehicle security and car stereo products and accessories available. The

recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic

technology, Directed Electronics is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America

and around the world.

Call (800) 274-0200 for more information about our products and services.

Directed Electronics is committed to delivering world class quality products

and services that excite and delight our customers.

Directed Electronics

Vista, CA 92081

www.directed.com

G562VL 07-06

Targus Mouse AMU41US User Manual
Telos Two Way Radio Zephyr Xport User Manual
Tiffen Camera Accessories Soft FX Warm Soft FX Filters User Manual
Trane Air Conditioner TCONT800AS11AA User Manual
Traulsen Refrigerator RHT132WPUT FHS User Manual
True Fitness Exercise Bike LC900 User Manual
Uniden Two Way Radio TR622 2 User Manual
ViewSonic Flat Panel Television VS12464 1G User Manual
Vizio TV Antenna M422i B1 User Manual
VXI Computer Hardware TC4XYY User Manual